Select the choice that answers the question correctly. Which of the following presents a safety risk to your workplace? a) Circuit breakers b) Grounding c) Blown fuses d) GCFI

Safety concerns encountered during power steering service should include all of these warnings, EXCEPT: Select one: a. power steering fluid can be very hot. b. beware of moving belts when the engine is running c. fluid pressure can be as high as 1,400 psi d. power steering fluid contact causes skin cancer.

The goal for the __ adjustment is to remove play at the worm bearings while maintaining a low resistance to worm shaft movement. Select one: a. Worm bearing preload b. Sector lash c. Tie-rod sleeve d. Clamp

All of the following are correct about four wheel steering systems in cars, EXCEPT: Select one: a. improved high-speed handling b. improved maneuverability during parallel parking c. improved maneuverability during U-turns. d. improved high-speed fuel economy.

The horsepower input to a pump is called __ horsepower. brake electrical liquid total

In modern computer -controlled four-wheel steering, an actuator similar to a front rack- and-pinion assembly attaches to the rear steering knuckles with tie -rod ends. Select one: True False

Technician A says that in a recirculating-ball steering box when the sector gear and nut teeth are in a straight ahead position they have maximum free play or clearance. Technician B says that in a recirculating-ball steering box when the sector gear and nut teeth are in a straight ahead position they have minimum free play or clearance. Who is correct? Select one: a. Technician A b. Technician B c. Both Technician A and Technician B d. Neither Technician A nor Technician B

In order to work.the suture thread must absorb the beet solution.What kind of thread was selected for that purpose? microfiber cotton silicon nylon

The __ is designed to provide a collapsing cushion that decelerates the driver's head and chest during an accident. Select one: a. Collapsible steering wheel b. Collapsible steering column c. Air bag d. Air suspension

What prevents transmission from being put in two gears at the same time? Select one: a. Shift rail detent balls and pins b. Shift rail interlock system c. Narrow shift gates d. A larger shift finger

Hot Questions

Select the choice that answers the question correctly. What should you do when inspecting battery-operated lifts? a) Contact the manufacturer before inspecting b) Open the battery compartment to see if the cells are properly sealed c) Make sure the lift is plugged in during inspection d) Operate the lift before inspecting

Technician A says that the most efficient method of EVAP system leak detection is introducing smoke under low pressure from a machine specifically designed for this purpose. Technician B says that nitrogen gas pressurization uses nitrogen gas under a very low pressure (lower than 1 psi) in the fuel system; you listen for escaping air with amplified headphones. Who is correct? A) Technician A B) Technician B C) Neither Technician A nor B D) Both Technicians A and B

For two single-phase transformers to operate satisfactorily in parallel, they must have the same voltage ratio and __ a. different percent impedances b. different turns ratios c. opposite polarities d. the same percent impedance

Isolated ground receptacle is an insulated grounding conductor that is run from neutral terminal at the main service entrance to the isolated ground terminal on the receptacle. True False

How do we calculate the "Wing Area" of an airfoil? Divide the maximum chord width by the span Multiply the mean camber by the span Divide the span by the average chord width Divide the minimum chord width by the span Multiply the span by the average chord width

A delta-connected three -phase alternator is driving a wye-connected resistive load. The alternator output voltage is 960 V.The load resistors are $12\Omega $ 12 Q each. What is the phase current in the alternator? 80 Amps 26.66 Amps 20 Amps 40 Amps

You should loose the lug nuts one by one in a clockwise position. True False

Question 17 of 32 A scientist is working to develop a new adhesive material. What is the best way for the scientist to accomplish this goal? A. To discuss ideas with scientists who have similar perspectives and training B. To work with a variety of scientists with different ideas and backgrounds C. To share ideas with other scientists but disregard opposing opinions D. To work alone until the material is developed

Cite three examples to describe how an engineer ensures that his or her designs are made to scale.

Which of the following is important for the maintenance of a single piston floating caliper? Front wheel bearing adjustment Positioning of caliper piston Slider to caliper body clearance Caliper to Piston bore clearance