Technician A says the R150 transmission has a countershaft that the transaxle does not have. Technician B says the C50 transaxle has a differential within the transaxle assembly that the R150 transmission does not. Who is right? Select the correct option and click NEXT. A only B only Both A and B Neither A nor B

Technician A says that the conical spring in the release cylinder causes the release bearing to maintain contact with the diaphragm spring Technician B says that the clutch cover diaphragm spring causes the release cylinder piston to be pushed into the cylinder, against the tension of the conical spring. Who is right? Select the correct option and click NEXT. A only B only Both A and B Neither A nor B

During the synchronizing process, additional pressure on the synchronizer ring is needed to bring the speed gear to the speed of the synchronizer sleeve. Technician A says the tapered end of the hub sleeve splines contacting the tapered teeth of the synchronizer ring provides the additional pressure. Technician B says the synchronizer key pulls the key spring and clutch hub into contact with the side of the speed gear providing additional pressure. Who is right? Select the correct option and click NEXT. A only B only Both A and B Neither A nor B

What should you do if you see a LOTO Lock or Tag device on a belt system? Select the correct answer. Check first, then start the belt to retrieve the stuck bags Crawl onto the belt system to check it out Leave it alone and do NOT remove the device

Select the choice that best completes the following statement. When you are installing your hose assemblies, it is extremely important for you to assure that the: a) Hose has a smooth bend b) Fitting is properly lubricated c) Hose is in a twisted position d) Outside collar on the hose end is tight

Select the choice that best answers the following question. Which of the following statements is true regarding the O-Ring Boss used in hose fittings? a) It requires the use of a sealant b) It uses an external O-Ring Seal c) It uses an internal O-Ring Seal on the face of the fitting d) It is most commonly used on steel tube assemblies II

Select the choice that best completes the following statement. When installing a hose assembly, insure proper sealing by: a) Using hose clamps b) Exceeding the hose's minimum bend radius c) Applying specified torque to the fittings d) Using proper sealant on all the threads irrespective of its type

Select the choice that best completes the following statement. Exceeding the hose's minimum bend radius in a non-reinforced hose will: a) Damage the steel braids b) Create weak spots c) Cause restriction of the medium flow d) Loosen the hose fittings II

Select the choice which best answers the following: When is the seal chamber cover installed? a) Before sliding the gland plate over the shaft b) Before lubricating the O-rings c) After positioning the mechanical seal d) After securing the shaft 00

Select the choice which best answers the following: Prior to mounting the pump, measure runout on the: a) Pump frame b) Impeller c) Motor shaft d) Mechanical seal

Hot Questions

9 Multiple Choice 1 point Which of the following is not a measurement function of a DMM? Pressure Voltage Continuity Resistance

An oilless lubricating system uses a well or reservoir in the end bell. A True B False Question 8 Which of the following statements about replacement capacitors is false? A They should have the same capacitance value as the original. B They should have a capacitance value up to $25\% $ greater than the original. C They should never be undersized. D They may have a capacitance value up to $10\% $ greater than the original.

Split-phase motors use a(n) __ to disconnect the start windings as the motor approaches running speed. A unloader B VFD C squirrel cage rotor D centrifugal switch Question 12 On a capacitor-start,induction-run motor, a centrifugal switch or relay disconnects __ when the motor reaches about $75\% $ of its rated speed. A the start winding only B the start capacitor only C both the start winding and start capacitor D both the start capacitor and run capacitor

Just before lifting off a rotary wing pilot must check the weather at the scene for a medical transport. In addition the pilot must also: Know the condition of the patient. Check the weather at the receiving hospital. Inventory all equipment on board the aircraft. Know the experience of the crew setting up the landing zone.

Advantages of ECMs include the following, except __ A ability to maintain constant airflow B easily replaceable brushes C efficient performance D variable speed Question 22 Important motor information such as rated voltage time rating, insulation class frequency, phase, and horsepower can be found on the __ A motor frame B motor nameplate C bearings D shaft

Which type of discontinuity is NEVER visible during visual inspection? underbead cracking porosity toe cracks undercut

The NEC in Table 210.24 shows that the minimum conductor size for branch-circuit wiring is __ 16 AWG 20 AWG 18 AWG 14 AWG

424170 What is the minimum number of trenches that should be dug across a truck-bed, railcar, or barge to acquire a representative sample? 3 (three) 4 (four) 5 (five) 7 (seven)

Nickel alloys should not be heat-treated. Select one: True False

The operator interface audible alarm sounds when there is a hydrogen event. Select true or false. True False