Once you have done the engine assembly test buildup, and ensured that all the parts work fine, which of the following do you NOT do before the final assembly? a. Disassemble the engine. b. Clean the engine once more. c. Paint the engine. d. Perform a test to check if the components are working properly.

Technician A says that you should check piston to bore clearance with a dial indicator following piston and rod I installation. Technician B says check rod side clearance with a feeler gauge following piston and rod installation. Who is correct? a. Technician A b. Technician B c. Both Technician A and Technician B d. Neither Technician A nor Technician B

Technician A says carefully install piston rings with any marks facing the correct way. Technician B says piston rings can be installed in any direction because they are not directional. Who is correct? a. Technician A b. Technician B c. Both Technician A and Technician B d. Neither Technician A nor Technician B

Technician A says that some head bolts can be reused. Technician B says that some head bolts are torqued to their yield point. Who is correct? a. Technician A b. Technician B c. Both Technician A and Technician B d. Neither Technician A nor Technician B

While inspecting a planetary gearset: Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct? Technician A Technician B Both A and B Neither Anor B

What is the function of the mainshaft in a manual transmission? Lubricate internal parts. Deliver torque to the driveline. Control fuel flow. Increase oil pressure.

Technician A says that a clutch is fully disengaged when the pedal is all the way up. Technician B says a clutch is released when the pedal is moved from full travel to the floor. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither Anor B

Which type of communications equipment functions as a radio receiver and searches across several frequencies? Scanner Duplex station Simplex station Mobile repeater

The minimum required amount of interocclusal space for a layered ceramic crown is .5 mm. 1.0 mm. 1.5 mm 2.0 mm.

What should be avoided during electrical storms? going close to open flames touching metal objects driving vehicles using a phone

Hot Questions

What does the Kiva Safety Info Service (KSIS)help validate and troubleshoot? Inventory discrepancies Safety-related behavior and PSC connections. Drive battery life issues System Administration

An electrician is installing a receptacle for a new clothes dryer. Although the cord for the dryer is six feet, at what distance from where the cord connects to the appliance is it recommended that he or she install the receptacle? A) Less than 1 foot B) Within 4 feet C) Within 2 feet D) Within 5 feet

What technology was used to observe the surroundings without exposing oneself above the trench line? periscope grenade stalemate

Some fixed ladders have lifelines that connect to a body harness. How long must the connection between the harness and lifeline be? 9 inches or less in length 10 to 12 inches in length 14 inches in length Proportional to the worker's height

Buck-boost transformers can be wired with __ polarity to boost the source voltage. a. additive b. cancellation c. neutral d. subtractive

Select the choice that answers the question correctly. What should you do when inspecting battery-operated lifts? a) Contact the manufacturer before inspecting b) Open the battery compartment to see if the cells are properly sealed c) Make sure the lift is plugged in during inspection d) Operate the lift before inspecting

Technician A says that the most efficient method of EVAP system leak detection is introducing smoke under low pressure from a machine specifically designed for this purpose. Technician B says that nitrogen gas pressurization uses nitrogen gas under a very low pressure (lower than 1 psi) in the fuel system; you listen for escaping air with amplified headphones. Who is correct? A) Technician A B) Technician B C) Neither Technician A nor B D) Both Technicians A and B

Isolated ground receptacle is an insulated grounding conductor that is run from neutral terminal at the main service entrance to the isolated ground terminal on the receptacle. True False

For two single-phase transformers to operate satisfactorily in parallel, they must have the same voltage ratio and __ a. different percent impedances b. different turns ratios c. opposite polarities d. the same percent impedance

You should loose the lug nuts one by one in a clockwise position. True False