True or False: The best way to inspect a tire is by rubbing you hand over the tread.
True or False: You should never remove the oil filter until you've successfully drained all of the oil and replaced the oil plug. It's important the oil drain plug never leaves your hand.
True or False: When replacing the oil plug, you should always begin threading by hand.
True or False: If the differential, or other components, cannot be checked during your inspection (Step #7), the vehicle will need be immediately moved to access these parts.
True or False: The differential plug should be kept in your shirt pocket to avoid dropping it while checking the differential fluid level.
All 15-20 amp receptacles in a dwelling must be what type? GFCI AFCI Locking Tamper resistant
TODAS LA MEZCLAS DE REFRIGERANTE TIENEN QUE CARGARSE AL SISTEMA EN FASE LIQUIDA. FALSO. VERDADERO.
Which of the following is true? Protective Equipment and Personal Protective Equipment (PPE) in good condition must always be used when performing any service or repairs on any part of the high-voltage electrical system Always follow the safety warnings in the published service information Both of the above Neither of the above
An AWD EV can be towed with two wheels on the ground. True False
If solid wire is nicked during the stripping process, a good practice is to __ Smooth out the wire with a file Repair the wire using solder Cut and strip the wire again Splice the wire with another wire
Multiple Choice 20 points What should you do if your electric breaker keeps tripping? Just turn it back on Contact an electrician See if you can fix it yourself Put a penny in it
Valve stem height is most critical on which of these? Select one: A. Non -adjustable solid lifter systems B. Adjustable solid lifter systems C. Adjustable hydraulic lifter systems D. Overhead cam engines
10) What tools are needed to measure $1/2$ T of oil?
air out of the tire? A. If the recommended psi is above the number on the gauge, add air until it reaches the recommended number B. If the recommended psi is below the number on the gauge, let air out until it reaches the recommended number C. If the recommended psi is below the number on the gauge, add air until it reaches the recommended number 3. When should you inflate or let 1 poin D. Inflate the tire until you hear a click and the air compressor stops inflating
An engineering professional must obtain a Master's Degree in engineering from an ABET- accredited program and must adhere to a code of ethics. True False
If door glass falls to operate after installation, the first step is to check electrical connections. A) True B) False
What should the operator do if there are marks from the articulating paper on the sealant after checking the occlusion? a. Remove and replace the sealant b. Remove high spots with finishing burs c. Apply additional sealant to improve coverage d. Apply the curing light for a few additional minutes
Which type of chains sprockets have annular rings? Detachable Roller Pintle Silent
A(n) __ is used in a pulling motion to smooth and shape the floor of the cavity preparation. a. hatchet b. hoe c. chisel d. excavator
Tool Required:Depth Micrometer 19.Which way do you turn the lock nut to engage and disengage the lock on the depth rod and how far does it turn? a. Engage clockwi se/Disengage counterclockwise b. Disengage clockwise/Engage counterclockwise 20.With the lock nut disengaged turn the thimble counterclockwise what happens to the depth rod? a. It retracts b. It extends c. Nothing 21.Turn the thimble clockwise, without returning to "zero" and describe what hap- pens? a. It retracts b. It extends c. Nothing 22.Now do the same thing using the ratchet stop/speeder.Is there a difference in resistance? a. Yes b. No 23.Lock the depth rod with the lock nut and attempt to turn the ratchet stop! speeder. What happens? a. Nothing b. The depth rod moves and the ratchet does not click c. The depth rod moves and the ratchet clicks d. The depth rod does not move and the ratchet clicks 24.Using the ratchet stop/speeder return the micrometer to the "zero position on the sleeve. Is the measuring rod flush with the base? a. Yes b. No 25.Replace the 0 -1" measuring rod with the $1-2''$ measuring rod. Turn the thimble to the "zero" on the sleeve. Does the measuring rod extend out of the base? a. Yes b. No
