To ensure your battery's longevity,you should: recharge it'at night keep the area where cables are connected to the positive and negative poles clean make sure you are changing the battery fluid regularly have it checked by a mechanic weekly
What is true of a second application of hard wax while the first is setting? Select the correct response: The first application must be with soft wax. The second waxing must be performed on an immediately adjacent area. It cannot be performed on an immediately adjacent area. The second application will make the service more thorough but less expedient.
Why is the travel and work angle important? Because of the jetting force of the electrode end. Because it affects the amount of spatter produced. Because of the force on the welding electrode holder the welding cable has as you move along the weld. They are not important and have little effect on how welds are made.
Electrodes with __ produce welds with the heaviest slag covering the molten weld pool and finished weld bead. cellulose-based fluxes rutile-based fluxes mineral-based fluxes silicon-based fluxes
When you add radiator fluid to the reservoir,how full should it be? Select the correct answer and click Submit. ) Up to the "Full"mark Up to the very top of the reservoir Up to the "Add"mark
Where is the transmission dipstick normally located on a rear-wheel drive vehicle? Select the correct answer and click Submit. At the rear of the engine near the firewall Directly above the steering column and in the middle of the engine At the front of the engine
Which of the following is a key activity in performing tire service and wheel balance? a. Cleaning the battery terminals b. Checking and adjusting tire pressure c. Inspecting the exhaust system d. Changing engine oil
The purpose behind permitting the grounding electrode connection to be made at the equipment grounding conductor terminal bar of the service rather than to the neutral is to provide a convenient connection point sometimes outside the service disconnecting means enclosure. True False
If 240-volt delta connected systems are not grounded, the voltage to ground is considered 240 volts. the installation is not in compliance with the NEC. the system is required to be grounded. a grounding electrode for the equipment is not required.
The typical voltages for a 120/240 volt, 3-phase, 4-wire delta-connected system are 120 volts phase A to phase B. ) 208 volts phase B to ground. 208 volts phase B to phase C. 240 volts phase C to ground.
Plastic components should be wiped with Motorcraft Metal Surface Prep Wipes prior to applying the RTV on the plastic component. A) TRUE B) FALSE
Select the correct answer and then click the Next button. Which coating classification BEST describes the presence of defects, but no serious corrosion? a. Good b. Fair c. Poor d. Bare
Select the correct answer and then click the Next button. What can interrupt cathodic protection and mask corrosion? a. Humidity b. Dissimilar metals c. Disbondment d. Static electricity
Select the correct answer and then click the Next button. What often causes pockets with corrosion grooves? a. Thin spots b. Wrinkled tape c. Holidays d. Air pockets
Select the correct answer and then click the Next button. What is the cause of premature pipeline corrosion? a. Keeping pipe aboveground b. Using cast iron pipe c. Coating failure d. Low product flow
Which type of slack adjuster is offered by most manufacturers because it resists over-adjustment? Select one: a. Stroke-sensing ASAs b. Clearance-sensing ASAs c. Manual slack adjusters d. Six-inch slack adjusters
Self-powered test lights are like regular test lights except that they contain a __ battery. Select one: a. 0.3-volt b. 24-volt C. . $12-volt$ d. 1.5-volt
What distinguishes a BIMODAL PV System from a UTILITY INTER-ACTIVE PV System? Bimodal has batteries Both are grid connected. Utility Interactive is cheaper
3. The engine in your car is sometimes called: A. A 4-stroke engine B. A 2-stroke engine C. An external combustion engine D. None of the answers
QUESTION: Which statement is true about the effects of ambient temperature on solid state devices? POSSIBLE ANSWERS: A solid state device is more likely to withstand excessive cold than excessive heat. The typical failure rate for a solid state device is $35^{\circ }C(95^{\circ }F)$ The failure rate for a solid state device doubles for every $10^{\circ }C$ that the temperature rises.
